Daptis

Training · October 22, 2026 · 4 min read

RPE and RIR: How to Use Effort to Train Smarter

RPE and RIR are two ways to say how hard a set was. RIR is the number of reps you had left. Lifting RPE is 10 minus that number. A set you ended with two good reps left is 2 RIR, or RPE 8. Using them lets your weights follow how you are on the day.

The short version

  • RIR is reps left in the tank. Lifting RPE is 10 minus RIR.
  • Aim for RPE 7 to 9 on heavy compound lifts and 9 to 10 on isolation work.
  • Rate right after the last rep, and check yourself against true failure on safe exercises now and then.
  • Effort plus reps gives an estimated 1RM, which is how you can let weights follow your day.

The scale

The lifting version of RPE was set out by Zourdos and colleagues in 2016, building on earlier work by Mike Tuchscherer. It ties each number to reps in reserve, which makes it far easier to use than a vague 1 to 10 effort scale.

RPERIRWhat it feels like
100Could not do another rep
9.50 to 1Maybe one more, maybe not
91One more rep, for sure
82Two more reps
73Three more, the bar still moving fast
6 and below4+Warm-up territory

Why use effort instead of fixed weights

Your strength changes from day to day. Poor sleep, stress or a hard week can take a few percent off; a good day adds it back. A program that says "100 kg for 5" is too heavy on a bad day and too light on a good one.

A program that says "5 reps at RPE 8" adjusts itself. You warm up, pick the weight that leaves about two reps in the tank today, and log it. Over time, your weights still climb, but they follow you rather than a spreadsheet. This is called autoregulation.

Effort also controls the dose. Research on proximity to failure finds that muscle growth improves as sets get closer to failure, while strength gains are similar across a wide range of RIR. So effort is not a detail: it is part of how much training you did.

How hard should each set be?

A simple guide most coaches would agree with:

  • Heavy compound lifts (squat, deadlift, bench, overhead press): RPE 7 to 9. Leave a rep or two so form stays clean and recovery stays manageable.
  • Other compound work (rows, lunges, presses with dumbbells): RPE 8 to 9.
  • Machines and isolation exercises (curls, raises, leg extensions): RPE 9 to 10. Going to failure is safe here and helps growth.
  • Technique work and deloads: RPE 6 to 7.
  • Warm-up sets: as easy as possible. They should never feel like work.

How to rate honestly

Most people underrate their effort at first. Research found lifters guess RIR better on heavier sets than on lighter, higher-rep sets, and get better with practice.

Rate the set right after the last rep, before you put the weight down: how many more could I have done with the same form? Not with a grind, not with a bounce. If your last rep slowed down a lot, you were probably at RPE 9 or higher.

Every few weeks, check yourself. Take a set of a safe exercise (a machine press, a curl, a leg press) to true failure and see how far off your guess was. It recalibrates you quickly.

Using RPE to pick tomorrow's weight

Effort and reps together give a decent estimate of your one-rep max. A common method: add the reps in reserve to the reps you did, then run the total through a formula like Epley's. 100 kg x 5 at RPE 8 is treated like 7 reps to failure, which works out to about 123 kg.

If today's estimate is higher than expected, the rest of your sets can go up a little. If it is lower, take some weight off rather than grinding through bad reps. Over weeks, the estimate is the cleanest way to see whether you are getting stronger.

Common mistakes

  • Treating RPE 8 as "hard": it means two reps left, which for many people feels harder than they expect.
  • Copying the plan's RPE into the log. Log what the set actually was, even if it was harder than planned.
  • Using it on the first set of a new exercise. Give yourself a session or two to learn it first.
  • Chasing RPE 10 on squats and deadlifts. Failure on heavy barbell lifts costs a lot of recovery and carries more risk.

How Daptis handles it

Every working set in a Daptis workout has a target RPE, and you log the RPE you actually hit. The app never copies the target into the log, because the point is how hard the set really was.

It uses that number straight away. Each finished working set gives an estimated 1RM (your RPE turned into reps in reserve, then the Epley formula), compared with what the plan expected. If you are stronger than planned today, the rest of your untouched sets move up; if you are weaker, they come down, rounded to 2.5 kg or 5 lb. The logger shows one line saying why, such as "Loads up 11% from your 130 x 6 @ 8". Your latest numbers then set the starting loads for the next workout. Free in early access on iPhone and the web; Android is coming soon.

Get a workout like this, adapted every day.

Daptis reads your recovery, your soreness and what you trained, then writes today's session and adjusts it as you log. Free while in early access.

Questions

What RPE should I train at to build muscle?

Most working sets between RPE 7 and 10, which is 0 to 3 reps in reserve. Go closer to failure on machines and isolation exercises, and leave a rep or two on heavy barbell lifts.

Is RPE the same as RIR?

They describe the same thing from opposite ends. RPE 8 equals 2 RIR. Some people find counting reps left easier than rating effort.

Should beginners use RPE?

Yes, loosely. Beginners rate effort less accurately, so start with a weight you could lift for a few more reps and use RPE as a rough guide. Accuracy improves within a few months.

Sources

  1. Zourdos et al. (2016). Novel resistance training-specific rating of perceived exertion scale measuring repetitions in reserve. J Strength Cond Res
  2. Helms et al. (2016). Application of the repetitions in reserve-based rating of perceived exertion scale for resistance training. Strength Cond J
  3. Robinson et al. (2024). Exploring the dose-response relationship between estimated resistance training proximity to failure, strength gain, and muscle hypertrophy. Sports Med
  4. Refalo et al. (2023). Influence of resistance training proximity-to-failure on skeletal muscle hypertrophy: a systematic review with meta-analysis. Sports Med